可能原因：加熱元件故障、水管堵塞或水閥問題。
Possible causes: Heating element failure, blocked water pipe or valve issues.

處理方法：更換加熱元件、疏通水管或修理水閥。
Solution: Replace heating element, unblock pipe or repair valve.

可能原因：咖啡豆過大、磨豆機故障或進豆通道堵塞。
Possible causes: Oversized beans, grinder malfunction or blocked bean channel.

處理方法：清理堵塞、調整磨豆機設置或更換磨豆刀片。
Solution: Clear blockage, adjust grinder settings or replace blades.

可能原因：排水管堵塞、排水閥故障或水泵問題。
Possible causes: Blocked drain pipe, drain valve failure or pump issues.

處理方法：疏通排水管、更換排水閥或修理水泵。
Solution: Unblock drain, replace valve or repair water pump.

可能原因：密封墊老化、水管破裂或接頭鬆動。
Possible causes: Aging gaskets, cracked water pipe or loose connections.

處理方法：更換密封墊、修補或更換水管、緊固接頭。
Solution: Replace gaskets, repair/replace pipes, tighten connections.

可能原因：系統檢測到故障、需要清潔或部件異常。
Possible causes: System detected fault, needs cleaning or component abnormality.

處理方法：系統診斷、清潔機器或更換故障部件。
Solution: System diagnosis, machine cleaning or replace faulty parts.

可能原因：電源線故障、保險絲燒斷或電路板問題。
Possible causes: Power cord failure, blown fuse or circuit board issues.

處理方法：更換電源線、更換保險絲或修理電路板。
Solution: Replace power cord, replace fuse or repair circuit board.

可能原因：主板燒毀、無法通電或程序故障。
Possible causes: Main board burned, no power or program failure.

處理方法：檢測主板、更換原廠或兼容主板。
Solution: Test main board, replace with original or compatible board.

可能原因：咖啡粉堵塞、壓力不足或萃取系統故障。
Possible causes: Coffee powder blockage, insufficient pressure or extraction system failure.

處理方法：清理萃取系統、調整壓力或更換故障部件。
Solution: Clean extraction system, adjust pressure or replace faulty parts.

可能原因：電路短路、元件漏電或功率超負荷。
Possible causes: Short circuit, component leakage or power overload.

處理方法：檢查電路、更換漏電元件或調整電源配置。
Solution: Check circuit, replace leaking components or adjust power configuration.

可能原因：初始化失敗、溫度感應器故障或系統錯誤。
Possible causes: Initialization failure, temperature sensor failure or system error.

處理方法：系統復位、更換感應器或重新編程。
Solution: System reset, replace sensor or reprogram.

可能原因：磨豆機馬達故障、齒輪損壞或控製板問題。
Possible causes: Grinder motor failure, gear damage or control board issues.

處理方法：修理或更換馬達、更換齒輪或修復控製板。
Solution: Repair/replace motor, replace gears or repair control board.

可能原因：加熱器故障、蒸汽管堵塞或壓力閥問題。
Possible causes: Heater failure, steam pipe blockage or pressure valve issues.

處理方法：更換加熱器、疏通蒸汽管或修理壓力閥。
Solution: Replace heater, unblock steam pipe or repair pressure valve.